DURO DYNE PINSPOTTERS

See Owners Manual MF-12 
See Parts Listing for MF-12  
See Spec Sheet for MF-12  

Duro Dyne's MF has been the standard for entry level "through insulation" welders for over 30 years.  Proven performance and high reliability have made the MF a "Must Have" for any sheet metal shop which does occasional insulating.  Duro Dyne now introduces the MF-12, building on that history, and creating a new pinspotter with greater power and versatility.  Special design welding transformers allow the MF-12 to deliver more power, precisely timed to the welding tip.  The new MF-12 will weld pins from 1/2 inch to 2 inches long on steel from 26 to 20 gauge.  Proven solid-state weld control circuitry guarantees years of reliable, trouble-free service in your shop.

See Parts Listing for MFPT

Replaced by the MF-12

Owner's Manual PBF-510
Parts Listing for PBF-510
Spec Sheet for PBF-510

Duro Dyne is proud to introduce the next generation of portable insulation fastening equipment.  Built upon the highly successful PBF pinspotter concept, the PBF-510 delivers more power, further away and with more control than ever before.  A new Multi-tap transformer allows the PBF-510 to deliver precise, timed low voltage to the welding tip.  This voltage will weld pins from 1/2 inch to 2 inches long on steel from 26 to 18 gauge.  Proven solid-state weld control circuitry guarantees years of reliable, trouble-free service in your shop.

See Parts Listing for PBFS

Replaced by the PBF-510

See FG Owner's Manual (PDF)
See Parts Listing for FG-15 (PDF)

Replaced by FG MACH I, FG MACH II 2003

The FG-15 has a five foot throat. Welds SSP, CP & FTC type fasteners to ductwork up to 16 Gauge. Requires 220 Volt, 50 to 60hz; fuse for 30 Amps. Source of 85 P.S.I. air required. Footswitch actuated, fasteners are inserted through the insulation and welded in place.

Adobe Acrobat Reader required to view FG-15 Parts.

See FG Mach I/II
       Owner's   Manual
       FG MACH l, ll Parts Listing
       FG MACH Dwell & Feed
       Assembly.
       FG MACH Frame Assy.
       FG MACH ll Power Pack
       FG MACH l Power Pack
       FG MACH Control Console
       FG MACH Component
       Module

• Two variations - standard 20 gauge capacity (FG Mach I) and Hi Power 18 gauge capacity with 2 inch pins (FG Mach II).
• Hi/Lo Switch - one flip of the switch adjusts for gauge thickness and or voltage variances.
• Digital function display.
• One adjustment controls weld and dwell times.
• Sleek streamlined frame design with 5 foot throat.
• Feed track proximity sensor -  for quiet operation.
• Digital weld setting indicator.
• Manual pin feed switch.
• Easy to access component case.
• Circuit breaker protection for the vibrator feed.
• Weld cycle indicator.

All FG MACH links are listed on the left and are PDF files.  
Adobe Acrobat Reader is required to open these files.

Replaced by  RH MACH II 2003

The RH Rolling Head Pinspotter welds SSP, CP & FTC type fasteners to ductwork up to 16 Gauge. Requires 220 Volt, 50 to 60hz; fuse for 30 Amps. Source of 85 P.S.I.  air required. Position fastener over insulation and depress trigger switch. Machine inserts the fastener through insulation and welds it to the steel. Select one of the links below.

RH Parts Listing
RH Parts Location Diagram
RH PP-3 Power Pack Diagram
RH Control Console and Feed Assembly Diagram
RH Trolley Diagram

RH MACH II Owner's Manual

• Digital circuit function display.
• One adjustment controls weld and dwell times.
• Sleek streamlined frame design with 5 foot throat.
• Feed track proximity sensor - for quiet operation.
• Posi-feed weld pin track release system.
• New Custom designed high performance weld transformer.
• 18 gauge capacity with 2 inch pins.
• Digital weld setting indicator.
• Manual pin feed switch.
• Circuit breaker protection for the vibrator feed.
• Weld cycle indicator.
• Flexlink wire harness and air line guide.